Homebase electronic twenty 20 program timer. Because the instructions were not enclosed, after finally getting around to. When AUTO OFF is shown the timer socket is currently off, when AUTO ON is. Asda; B&Q TE103; Bobway TA-L11; Chevron ew-32; Elro TE109; Essentials Digital Timer EW-32; Homebase 7 Day 24. Digital Timer is a useful tool for measuring time durations - for example, if you want to measure how long it takes for a program to run. Download.com has chosen not to provide a direct.

• AM/FM Digital Radio INSTRUCTION MANUAL www.tecsunradios.com.au. • Setting display backlight.. 11 Changing MW channel step.12 Setting display contrast..

13 Checking version..14 DRM memory.. 15 Setting the alarm timer..

Katalog cvetov ral wcp sayerlack italiya. Cs 001 cs 002 cs 003 cs 004 cs 005. Cs 006 cs 007 cs 008 cs 009 cs 010. Cs 011 cs 012 cs 013 cs 014 cs 015. Cs 016 cs 017 cs 018 cs 019 cs 020. Cs 021 cs 022 cs 023 cs 024 cs 025. Cs 026 cs 027 cs 028 cs 029 cs 030.

16 Setting snooze.. 18 Setting sleep timer.. 19 Setting confirmation beep.20. • Performing factory reset.21 Switching between DRM/AM/FM modes.22 Volume and Tone control.22 Manual tuning.. 24 Auto scan tuning..26 Presetting stations.. 27 Recalling a preset station.28 Line out..29 Headphone socket..

29 DRM memory tuning. • Thank you for choosing Tecsun Radios Australia product. Please read this manual carefully before operating the radio and keep it for future reference. Do not leave the radio near heat sources, such as heaters or hot air ducts, or in a place subject to direct sunlight, excessive dust, humidity, rain, mechanical vibration or shock. • To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Vernutj lyubimuyu devushku torrent. Never use an AC power cord that is damaged, route the power cord in a safe manner and make sure it is not exposed to sharp surfaces or the possibility of pinching.

• □ □ Display Controls □ Speaker www.tecsunradios.com.au. • □ □ Whip antenna Headphone socket □ FM external antenna jack Line out jack □ AM external antenna jack DC power jack □ □ Antenna switch AC power jack www.tecsunradios.com.au. • □ BAND selection button TUNING control rotary □ □ SERVICE selection MODE switch button □ □ VF/VM button Volume/Tone control rotary □ □ MENU, INFO button USB port □ POWER ON/OFF button MANUAL TUNE buttons □ PRESET buttons www.tecsunradios.com.au. • Frequency display □ □ Sleep indicator Metre band indicator □ □ Antenna indicator Time indicator □ □ Signal strength Mode indicator □ □ Stereo indicator Preset group-number □ DRM SERVICE indicator Tuning indicator □ □ Frequency dial VF/VM indicator www.tecsunradios.com.au. • AC operation Before plugging the AC cord into the radio, make sure the AC voltage is correct.

Insert the plug on the end of the supplied power cord into the AC power socket on the back of the radio. DC operation The radio can also be operated by connecting a 9V DC power adaptor with 2.5 Amp capacity and center positive polarity to the DC 9V jack on the rear panel. • The radio comes with built-in AM/FM antenna and external antenna. To use internal antenna, make sure to switch external/internal switch on the back of your radio to internal antenna position (i.e. As for external antenna, you can connect a coaxial cable of outdoor antenna (not supplied) to the BNC type antenna terminal. Press MENU/INFO button to enter the menu settings.

Rotate the TUNING control rotary until the ‘Time Set’ entry is shown on the display, then press it to enter the setting. An underline will be shown under the hour setting. Rotate the TUNING control rotary to select the desired hour, and press the rotary to confirm the setting. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Date Set’ entry is shown on the display, then press it to enter the setting.

An underline will be shown under the month setting. Rotate the TUNING control rotary to select the desired month and press the rotary to confirm the setting and proceed to day setting. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Backlight’ entry is shown on the display, then press it to enter the setting. Rotate the TUNING control rotary to adjust the backlight timeout between always off, 10 seconds, 30 seconds, 60 seconds and always on.

Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘MW Step’ entry is shown on the display, then press it to enter the setting.

Rotate the TUNING control rotary to adjust the MW channel step between 9 kHz and 10 kHz. Press MENU/INFO button to enter the menu settings. Rotate the TUNING control rotary until the ‘Contrast’ entry is shown on the display, then press it to enter the setting.